Leading 10 usual forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not underestimate the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are many accidents involving forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual ahead might not be discovered, leading to a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo surpasses the allowable size of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge have to be risk-free before starting.
3. When the forklift begins with a tons, the driver must initially verify that the lots is steady and reliable.
4. The begin must be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is taking a trip, the fork should not be elevated too high, which will affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the lorry ahead. .
7. When the forklift is running, the lots must remain in the most affordable placement that does not prevent the driving, and the gantry should be effectively slanted back. The lots will not be elevated other than when stacking or packing. .
8. The height of the load need to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of the two forks balanced and not manipulated, and one side of the product must be against the rack. .
2. It is prohibited to deal with a single fork or use a fork top or draw. In special circumstances, safety and security indication should be established to remind bordering pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is restricted to leave the Stand-on Electric Pallet Stacker forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the Electric Forklift Truck for Warehouse security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought to also be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844